Choosing safety glasses vs goggles comes down to the hazard in front of you. Safety glasses protect your eyes from impact hazards, such as flying chips and particles. Goggles sit close around the eyes. Non-ventilated and indirect ventilated goggles also guard against liquid splashes and fine dust, according to the Canadian Centre for Occupational Health and Safety (CCOHS).
For most safety glasses vs goggles decisions, wear safety glasses for impact work. Switch to indirect ventilated or non-ventilated goggles when liquid, chemicals or fine dust can reach your eyes.
What is the difference between safety glasses and goggles?
Safety glasses are worn like regular eyeglasses, on a frame that rests on your ears. CCOHS describes them as protection for the eyes from impact hazards. It also notes that safety frames are stronger than street-wear frames and are often heat resistant.
Goggles strap around your head and close the gap around your eyes. Direct ventilated goggles protect against impact hazards. Non-ventilated and indirect ventilated goggles add protection against chemical or liquid splashes and fine dust.
Face shields help protect the eyes, nose, mouth and face from impact hazards and from chemical or liquid splashes. For splashes, CCOHS lists a face shield worn over goggles with indirect ventilation.
The table below compares spectacles, goggles, hoods and face shields for four common hazards, following the CCOHS selection table. The class codes come from the Canadian Standards Association (CSA) Z94.3 standard for eye and face protectors.
| Hazard |
Example tasks |
Protectors listed |
| Flying objects |
Chipping, drilling, grinding |
Class 1A spectacles, Class 2A and 2B goggles, Class 5A and 5B hoods, Class 6A and 6D face shields |
| Flying particles, dust and wind |
Woodworking, sanding, concrete work |
Class 1A spectacles, Class 2A and 2B goggles, Class 5A and 5B hoods, Class 6A and 6D face shields |
| Acid splash and chemical burns |
Acid and alkali handling, degreasing |
Class 2B goggles, Class 5B hoods, Class 6A face shields |
| Abrasive blasting |
Sandblasting, shot blasting |
Class 2B goggles, Class 5B non-rigid hoods, Class 6A face shields |
Spectacles appear only on the impact and dust rows. Splash and blasting work moves you to goggles, a hood or a face shield. For splashes, CCOHS lists a face shield worn over goggles with indirect ventilation.
A Milwaukee angle grinder throws sparks at a fabrication bench. Grinding sits under the flying objects hazard in the CCOHS selection table.
When should you wear goggles instead of safety glasses?
Wear goggles when the hazard can get around a pair of glasses. Those hazards include liquid or chemical splash, irritating mists and fine dust.
CCOHS lists goggles with indirect ventilation for splashes, droplets and sprays, and goggles with no ventilation for irritating chemical mists. Direct ventilated goggles are listed for impact hazards only.
Whichever you pick, it has to be comfortable enough to wear. CCOHS warns that equipment that is uncomfortable or poorly fitted is unlikely to be worn. Eyewear should also fit comfortably over the temples and over the ears.
Eye protection for hydraulic work
Hydraulic work can combine flying debris and fluid splash in the same job. In a hose shop or on a service truck, match eye and face protection to the task, the equipment manufacturer’s instructions and the fluid’s safety data sheet (SDS).
Control pressure before servicing
Before disconnecting hydraulic lines or opening a circuit, follow the manufacturer’s isolation and lockout procedure, release stored pressure and verify that the circuit is depressurized. Eye protection does not make it safe to open a pressurized system.
| Task |
Main hazards |
Eye protection and controls |
| Cutting hose |
Flying rubber, wire and grit |
Wear impact-rated safety glasses with side protection. Add a face shield at the cut-off saw when required by the saw manufacturer’s instructions or task assessment. |
| Skiving and crimping |
Wire ends and metal chips |
Wear impact-rated safety glasses with side protection. Follow the machine manufacturer’s instructions and task assessment for any additional protection. |
| Pressure testing assemblies |
Fluid spray, ejected fittings and hose whip |
Use a suitable guarded test enclosure and follow the approved testing procedure. For splash exposure, use indirect-vented splash goggles with a face shield. Eyewear supplements the enclosure and other controls. |
| Disconnecting hydraulic lines after isolation and depressurization |
Residual fluid splash |
Verify that the circuit is isolated and depressurized before disconnecting. Wear splash goggles and add a face shield when required by the SDS, manufacturer’s instructions or task assessment. |
| Projectile cleaning |
Ejected cleaning projectiles and debris |
Follow the cleaning system manufacturer’s eye-protection and projectile-containment instructions. |
| Solvent cleaning |
Solvent splash and chemical exposure |
Select chemical splash goggles suited to the solvent. Add a face shield when required by the SDS, manufacturer’s instructions or task assessment. |
Select protection for the task using CCOHS eye and face protection guidance, the equipment instructions and the fluid’s SDS. See CCOHS solvent-handling guidance and HSE pressure-testing safety guidance for supporting controls.
Should you use safety glasses or goggles for pressure washing?
For pressure washing, check the operator’s manual for your machine to settle the safety glasses vs goggles question. The operator’s manual for the BE Power Equipment B347RX pressure washer tells operators to always wear safety (splash) goggles for eye protection. The reason given is that the high-pressure spray can launch debris at high velocity. A face shield is also recommended, and an eyewash kit should be kept available in case of emergency.
Ontario’s safety alert on high-pressure water-jetting guns covers a related hazard and points to section 81 of Regulation 851 (Industrial Establishments) and section 24 of Regulation 213/91 (Construction Projects). Under those sections, workers must wear eye protection when there is a risk of eye injury. The duty also applies when another worker nearby is at risk of eye injury. The manufacturer’s instructions on protective equipment should also be followed.
BE Power Equipment is one of the brands we carry. If you are choosing a machine, our commercial pressure washer guide covers the specs to check.
What does Ontario law require for eye protection at work?
In Ontario, Regulation 851 for industrial establishments sits under the Occupational Health and Safety Act (OHSA). Ontario’s guide to hazards in the industrial sector says employers must ensure, under section 81, that appropriate eye protection is provided to workers.
Section 124 applies where a worker works with, or is likely to be exposed to, a hazardous biological or chemical agent that could injure the eye or skin. It then requires the employer to provide eye wash facilities, emergency showers or flushing fluids as needed for adequate emergency treatment. Under section 79, workers required to wear protective equipment must be trained in its care and use.
Ontario law asks for eye protection that is appropriate in the circumstances, so the job and its hazards set the safety glasses vs goggles choice. Many jurisdictions in Canada require eye and face protection to meet CSA Standard Z94.3, CCOHS notes. CCOHS advises running a hazard assessment and then selecting protection for the hazards found.
Face injuries are common at work. The Association of Workers’ Compensation Boards of Canada (AWCBC) counted 10,215 accepted lost-time claims for face injuries across Canada in 2024.
10,215
accepted lost-time claims for face injuries across Canada in 2024
This figure counts accepted lost-time claims only, so injuries without an accepted claim are not included.
Can regular prescription glasses replace safety glasses?
No. CCOHS states that prescription eyeglasses are not considered eye protection.
Prescription wearers face the same safety glasses vs goggles decision. CCOHS says prescription glasses may be worn underneath face shields and some types of protective eyewear. Another option is prescription safety glasses that carry a certification mark.
5 checks for the safety glasses vs goggles choice
These five checks apply to safety glasses and goggles alike. They come from CCOHS guidance on eye protection and on running a protective equipment program.
Eye protection checklist
✓ Match the protector to the hazard: impact, dust, splash or mist.
✓ Look for the certification mark on the lenses and on the frame front and temples.
✓ Check coverage from the eyebrow to the cheekbone, with the frame up on the nose.
✓ Let workers try two or three models so the pair they pick actually gets worn.
✓ Replace eyewear that is scratched, pitted, broken or bent. Replace ill-fitting eyewear too.
Five quick checks cover the hazard, the mark and the fit. They also cover comfort and the condition of the lens.
1. Match the hazard. Use the CCOHS selection table above to settle the safety glasses vs goggles choice. Impact work and general flying particles and dust allow spectacles. Fine dust and splash work call for goggles with indirect ventilation or no ventilation.
2. Find the mark. CCOHS says the certification mark must be present on approved safety lenses and on the frame front and temples. Products approved by CSA bear the CSA certification mark.
3. Check the coverage. CCOHS advises that eyewear should cover from the eyebrow to the cheekbone. Glasses that sit halfway down the nose give less protection from flying particles, sometimes none at all.
4. Test the comfort. Workers should be able to choose among two or three models, CCOHS suggests, because uncomfortable or poorly fitted equipment is unlikely to be worn.
5. Replace worn eyewear. Scratches impair vision and can weaken lenses. Replace any device that is scratched, pitted, broken or bent. Replace ill-fitting devices too.
Our health and safety range covers personal protective equipment (PPE), including gloves, eyewear, respirators and hearing protection. It also includes first aid supplies such as eyewash stations. We offer technical advice for compliance and product selection, plus custom sourcing for specialized equipment. Our guides to hearing protection and cut-resistant glove levels cover two more parts of the kit.
Frequently asked questions about safety glasses vs goggles
Are safety glasses enough for grinding?
They can be. The CCOHS selection table lists spectacles, goggles, hoods and face shields for grinding, under the flying objects hazard. Your hazard assessment and the grinder manufacturer’s instructions decide which one fits. If fine dust or splash is also present, CCOHS lists non-ventilated and indirect ventilated goggles for those hazards.
What is CSA Z94.3?
CSA Z94.3 is the Canadian standard for eye and face protectors. CCOHS notes that many Canadian jurisdictions require eye and face protection to meet it. The standard sorts protectors, such as spectacles, goggles and face shields, into classes for particular hazards.
Can a face shield replace safety glasses or goggles?
Treat a face shield as an added layer. For chemical splashes, CCOHS lists a face shield worn over goggles with indirect ventilation. Its chainsaw guidance adds that a face shield attached to the hard hat without safety glasses does not provide adequate eye protection.
The safety glasses vs goggles choice starts with the task and the hazard. Tell us what your crew is doing and we will help you compare eyewear for the job. Call our Barrie location at (249) 315-4673 or our Concord location at (905) 760-1711, or contact us online.